Hall Tree – How to build one from scratch

Recently a friend asked me to design and build a hall tree for her entryway. Her husband farms, and she was tired of his muddy boots on her floors! She sent me some pins (Pinterest) of what she was thinking. I designed the piece two different ways for her using Google Sketchup. One as a corner unit, the other as a single bench.

halltree3

Google Sketchup is a free drawing software package, that is fairly quick to to learn (lots of tutorials on Youtube). This was my first time using it, normally I draw my plans by hand, or with AutoCad. Using something like Sketchup lets you work out a lot of details before you ever start cutting wood. For example, getting the crown molding right, or deciding what the bracket for the seat should look like. Also, for most of us, it is much easier to “see” in 3d, instead of seeing it in a normal drawing view.

Because this is a painted piece, I chose to use cabinet grade plywood for the bench box. The corners of the box are mitered, with 1″x1″ reinforcing blocks glued and screwed inside, to help support an adult’s weight. Take your time setting up the table saw for this type of joint, getting everything square, and the corner joints will be tight.

box

The seat is a combination of plywood and pine, with the edges wrapped with screen molding. This means there are now plywood edges to be seen.

seat

Because I have the tools, and the raw lumber, I chose to build the frame for the back from maple. I jointed and planed the boards to size, followed by creating the mortise and tenon joints and a dado for the bead board for the back panel.

lumber

rabbet

I glued the frame together, and clamped it overnite. The bead board was inserted and pinned in place. The bead board locks together on the edges greatly helping with alignment for the long haul.

back

Next I focused on the crown molding, realizing after I had it wrapped nicely around the top, that it would be too wide to fit into its planned location. So I redid it flush to the panel edges.

crown 1

crown 2

I bolted the back to the box, so it could be removed for shipment, or re purposing of the box later.

The corner brackets are cut using a bandsaw (or jig saw or even a coping saw). these were made from 2×12 and screwed to the back and the box top.
corner bracket

Once the applique was glued to the front and the feet added to the bottom, it was time to paint!

white

I sprayed the entire unit with a white base coat. I used an inexpensive HVLP gun from Harbor Freight.

The next day I antiqued it with stain. I brushed it on, and wiped it off, trying to give it the aged look our friend had asked for. Once dry I added the hinges and we delivered the piece to her home.

done

3 thoughts on “Hall Tree – How to build one from scratch”

  1. Greetings from Carolina! I’m bored to tears at work so I chose to browse your
    site in my iphone during lunch break. I
    really love the knowledge you present here and can’t wait to have a look when I return home.

    I’m shocked at how quick your site loaded in my mobile phone
    .. I’m not even using WIFI, just 3G .. Anyhow, superb site!

  2. How did you build the seat that opens/closes? I have a hall tree that has a fake wood seat that opens and closes and was thinking about adding a real wood seat.

    Thank you!

    1. Because the intended user was a local farmer, and his wife wanted him to use it to change his work boots, I knew it would take some abuse. I could not use the full panel because I wanted the angle supports on the sides. I created a three sided frame, (2 sides and back) that rests on the box sides. Then I glued and screwed ledgers under the two sides. These were 1×3’s that hung into the opening about an inch. They supported the lid, along with the front edge of the box, so the hinges did not have to take all of the weight.

Leave a Reply to Dan Cancel reply

Your email address will not be published. Required fields are marked *